Hydraulic tube fittings can not be used to replace ordinary dedicated connector

In the hydraulic system, either a metal hydraulic tube fittings, hoses or fittings, are prone to leakage problems. For card sets of pipe joints, mostly due to the pipeline by a larger force or impact, so that the card sleeve loose or pipe end surface deformation caused by leaks, you should check whether the card sets out of round, edge or without defects, whether the pipe ends in good condition and the extent of compression hydraulic tube fittings nut, but also eliminate the pipeline force. For flared tube hydraulic tube fittings, mostly due to excessive flaring, substandard quality requirements or repeatedly demolished, resulting in flaring deformation or cracks caused by leaks, then you can be re-flared front amputated.Hydraulic tube fittings in the hydraulic system, the connecting member and the pressure tubing hydraulic tube fittings  tubing between. If you use a male and female cone top pressure seal, which is mostly due to the two cone leak damage, is available on the cone grinders for grinding. For use oil sheet, wool felt, soft steel board, combination gasket sealant joints or pipe leaks, no matter what the material is, you should first check the seals for damage, deformation, aging and rough through the large, etc. and then take the appropriate measures.Hydraulic tube fittings can not be used to replace ordinary dedicated connector, because the hydraulic are can withstand a lot of stress.

How to buy and use metal hose

Metal hydraulic hose manufacturers occupied in modern industry's position was certain. However, if the selection is not correct, the use of unreasonable or not installed properly, could not get ideal effect, even caused serious economic losses. Therefore, the engineering design personnel, operation and repair personnel, all kinds of metal hose connector on the proper use of knowledge must have a basic understanding of.
The selection of the length of
"Hose, can be short or long". However, metal hose working conditions often due to determine the length of inappropriate, caused by this or that problem. For example: metal hose compensator used for too long, will produce the instability; the pump inlet, pump outlet used metal hose is too long, will produce the additional vibration; metal hose is too long for the pipeline system, will produce large fluid resistance etc.. Of course, put them to shorten the length of some, there can avoid these problems. However, blindly shorten. It is impossible to achieve compensation, vibration, noise elimination purposes. At the same time, the superiority of the metal hose in other aspects are not fully reflect. So, to determine the metal hose length is a very important work.
(1) as a metal hose compensator for, its length depends on the diameter size. The following basic principles: the calculation of diameter less than or equal to 250 mm, diameter less than or equal to 400 mm in diameter, that is less than or equal to 1000 mm,: in the pipeline system, if the compensation of a compensator is not enough, you can use two, three....... If by spatial location conditions, compensator may not install a plurality of, can choose a duplex structure. But the formula (7. (7, 1). (7, 2). 3) principle shall not violate.
(2) for the vibration, the elimination of the pump inlet, pump outlet pipe with noise, depends on the length of the path size, i.e. diameter less than or equal to 100 mm, formula (7. 1) ~ (7. 4), the L compensator or metallic flexible hose length; for the compensator or metal hose diameter.
(3) metal hose angular displacement, length depends on the actual bending radius and displacement angle. That is, (4) metal hose of lateral displacement, length depends on the actual bending and transverse displacement radius size. That is: cut the line refers to the time of the lateral displacement of the metal hose, transitional stage two of the same radius, different direction bending pipe. The calculation, according to the times of the diameter generally consider the length of.
(5) in the bending state, parallel longitudinal movement of the metal hose length depends on the actual bending radius and longitudinal movement quantity. That (6) in the bending state, the parallel sections of lateral movement of the metal hose length depends on the actual bending radius and the transverse moving volume size). That is the formula (7. 5) ~ (7. 2), and L is a metal hose flexible segment length; for metal hose diameter; displacement angle; Y is a single horizontal displacement; T is the total displacement of longitudinal or transverse quantity.

The difficulties and challenges to the development of the industry of stainless steel metal hose

Stainless steel metal hydraulic hose fitting played an important role in modern industry, the application in civil field has a lot of. Under the new situation, the development of the industry is facing many difficulties and challenges, major companies have to show a positive attitude to deal with.
1, technical improvement and independent R & D capacity further enhanced.
A to speed up the construction of industrial innovation system, promote the development of the technology of stainless steel metal hydraulic hose manufacturers and industrial application;
The development of B production of environmental protection and recycling economy, the implementation of national and industry targets of energy saving and emission reduction task, to ease the resource and environmental constraints;
C promotes the stainless steel metal hose industry in a combination of fiber, high-end equipment, energy saving and environmental protection, brand marketing and other aspects of the national strategic emerging industry, cultural industry, especially stainless steel metal hose products in new materials, new energy, energy saving and environmental protection, new strategic innovation in the field of development and application of fiber industry and closely integrated development model.
Enhanced 2, property right consciousness. The relevant government departments to vigorously popularize the knowledge of intellectual property rights, enhance the awareness of intellectual property of metal hose of stainless steel of small and medium sized enterprises. To carry out special training, develop intellectual property management personnel for metal hose of stainless steel of small and medium sized enterprises. Patent counseling, patent agency, patent early warning and patent service stainless steel metal hose is small and medium-sized enterprise activities, cultivate and form a group with independent intellectual property rights of the advantage of the metal hose of stainless steel of small and medium-sized enterprises, improve the industry of small and medium-sized enterprise creation, utilization, protection and management ability of intellectual property.
3, improve the quality and standard management. Small and medium enterprises in the industry to carry out quality commitment activities, establish a quality credit system, improve the quality of honesty and self-discipline level. Small and medium-sized enterprises to strengthen brand building guidance, provide technical support for the stainless steel metal hose of small and medium - sized clothing enterprises to enhance brand value. Promote the industry of small and medium-sized enterprises to actively carry out activities to create a standardized good behavior enterprises, improve standardization level of management.
To be the common role of the government and enterprises development of stainless steel metal hose industry, in government for the industry overall macro control, the difficulties and challenges will be transformed into effective motivation development.

DKJ connector

DKJ connector layout and characteristics: DKJ card type of flexible metal hydraulic hose adapters, steel and hose connections will be no threads, save the threading process, only the screw is screwed into the can; metal joint is made of zinc alloy material by die casting, surface galvanized, frosted, or chrome plated; layout tight, high strength. Reliable, connection pipe and the metal hydraulic hose assemblies surface is beautiful; the metal joint for sleeve type, stainless steel metal hose to the metal hose connection on the steel pipe is threaded metal hose; adaptation: JS type, JSH type, JSB type, JSHG type; adapting pipe: a thin steel wire tube, black and galvanized iron pipe (water, gas pipe); use DKJ card type metal joint note standard, scale steel hose connection.

The points for attention in installation of high pressure rubber hose connector

High pressure hose installation whether metal pipe joint, or hydraulic hose and fittings connector, are prone to leakage problems, any kind of product the installation process is the most important,is to ensure that the product is installed after the premise of normal use, thus the following should be noticed everybody simple introduction about some high pressure hydraulic hose couplings joint during installation question: (1) tube in the moving or static, cannotexcessive bending, nor in the root bend, at least to start bending at 1.5 times thediameter of the office; (2) hose moved to not pull too tightly extreme position, should be more relaxed; (3) to avoid deformation hose (torsion; 4) hose as far away as possible from the heat radiation member, necessary fashion insulation board; (5)should avoid hose external injury, such as isomorphism parts use long-term frictionsurface; (6) if the hose weight caused by excessive deformation, should support.

Hydraulic ferrules cold deformation, flaring, flattening no cracks

Hydraulic ferrules is one of the three parts of the card sets of pipe joints (ferrules, nuts, seamless steel pipe) composed. Hydraulic ferrules working principle is the seamless steel insert card kit, ferrule nut using inconsistent card sets, card kit seamless steel blade evenly cut, form an effective seal. Hydraulic ferrules type straight pipe hydraulic flanges are widely used in oil refining, chemical, oil, gas, food, pharmaceutical, and other instruments. Hydraulic ferrules high accuracy, good finish, inside and outside the walls of the heat pipe no oxide layer, the hydraulic hose assembly wall of cleanliness is good, pipe withstand high pressure. Hydraulic ferrules cold deformation, flaring, flattening no cracks, deformation and can make a variety of complex mechanical processing. Hydraulic ferrules joints inside and outside the installation need to take over the interface and connection fittings are handling clean. Be sure to take over the mouth of the polished smooth surface can not have glitches and uneven surfaces.

Hydraulic hose

Hydraulic hydraulic hose manufacturers is mainly composed of an inner rubber layer, the adhesive layer, liquid resistance in 2 or 4 or 6 layers of spiral steel wire reinforced layer, cover, the inner layer is putting pressure on the transport medium, the protection of wire is not affected by erosion, outer layer protection wire is not damaged, the steel wire layer is the skeleton material enhancement effect. Hydraulic power transmission or conveyance of water, gas, oil and other high pressure medium, so as to ensure the liquid circulation and transfer the liquid energy. Characteristics of the 1 hydraulic hose adapters adopts special synthetic rubber made with, has excellent oil resistance, heat resistance, aging resistance performance. Closely, combining the 2 pipe body soft, under the pressure of small deformation. The 3 hose has excellent flexibility and fatigue resistance.

Structural classification of fast joint

Both ends of the opening and closing
Do not link: when the mother's ring moved to the other end, stainless stainless steel hydraulic fittings bead automatic roll out, the operation force sub body due to maternal and child body together the valve spring force the valve closed and disconnected, their progeny and parent, instant block fluid flow. Link: when body is inserted into the population, ring back to the original position under the action of a spring, a steel ball rolling lock sub body tightly connected, and parent and progeny promote each other and open the valve, fluid flow, the O ring can completely block the leakage of fluid.
With two open ends
Do not link: when the mother's ring is pushed to the other end, the steel ball automatic roll out, therefore, the sub body is removed; because the child body and parent are no valves, fluid flowing outward. Link: when body is inserted into the maternal, force the spring ring is pushed to the previous location to the steel ball lock, fluid flow, the O type ring to prevent liquid leakage
Single channel opening and closing
Do not link: when the mother's ring moved to the other end, stainless steel metal hydraulic hose adapters automatic roll out, progeny is the valve spring counterforce spring open, the valve can automatically close to block fluid flow. Link: when body is inserted into the maternal side ring, the valve is opened lead to fluid flow, the washer is the force of the spring back to the original position, stainless steel beads will lock to ensure that the child / parent connection, the inside of the washer can completely block the leakage of fluid.

The points for attention in installation of high pressure rubber hose connector

High pressure hose installation whether metal pipe joint, or hydraulic hose and fittings connector, are prone to leakage problems, any kind of product the installation process is the most important,is to ensure that the product is installed after the premise of normal use, thus the following should be noticed everybody simple introduction about some high pressure hydraulic hose couplings joint during installation question: (1) tube in the moving or static, cannotexcessive bending, nor in the root bend, at least to start bending at 1.5 times thediameter of the office; (2) hose moved to not pull too tightly extreme position, should be more relaxed; (3) to avoid deformation hose (torsion; 4) hose as far away as possible from the heat radiation member, necessary fashion insulation board; (5)should avoid hose external injury, such as isomorphism parts use long-term frictionsurface; (6) if the hose weight caused by excessive deformation, should support.